Edexcel International A Level Physics

Topic Questions

International A LevelPhysicsEdexcelTopic Questions6. Practical Skills in Physics IIPractical Skills II: Analysis

Practical Skills II: Analysis

DownloadView
Medium
1a
Sme Calculator4 marks

An L-shaped steel rod was held horizontally in a stand clamped by its shorter end as shown.

q4-wph16-06-oct-2021-edexcel-int-as-and-a-level-phy

The end of the steel rod was at a height p above the bench.

A student attached a mass m to the end of the steel rod causing it to bend towards the bench. The end of the steel rod was then at a height q above the bench.

i)
Describe two techniques she should use when measuring p and q.

(2)

ii)
The difference between p and q was recorded as 26 mm ± 1 mm.

Explain why the uncertainty in this value is given as 1 mm.
(2)

How did you do?

1b
Sme Calculator6 marks

The steel rod had a circular cross-section with a diameter d of approximately 2 mm.

i)
Explain the most appropriate instrument the student should use to measure d.
(2)
ii)
Explain one technique that she should use to measure d.
(2)
iii)
She recorded the following measurements.

d / mm
2.35 2.37 2.34 2.35 2.33

Calculate the mean value of d in mm and its uncertainty.

(2)




Mean value of d = ......................................... mm ± ....................................... mm

How did you do?

1c
Sme Calculator2 marks

The shear modulus G is a measure of a material’s resistance to bending, and is given by   
      G equals fraction numerator 32 m g l x squared over denominator pi y d to the power of 4 end fraction

where m is the mass attached to the end of the rod and y is the vertical deflection.

l and x are the lengths as shown below.

q4c-wph16-06-oct-2021-edexcel-int-as-and-a-level-phy

Determine a value of G for steel in N m−2.

m = 100g with negligible uncertainty
l = 58.9 cm ± 0.1 cm
x = 10.3 cm ± 0.1 cm
y = 26 mm ± 1mm




G = ............................................................ Nm−2

How did you do?

1d
Sme Calculator4 marks

The table shows values of G for different types of steel.

Type of steel Structural steel Carbon steel
G / 109 Nm−2 79.3 77.0

Deduce whether the data provided in part (c) would allow the student to determine the type of steel the rod was made from.

How did you do?

Did this page help you?

2a
Sme Calculator4 marks

A student investigated standing waves using the apparatus shown.

q3-wph16-06-oct-2021-edexcel-int-as-and-a-level-phy

The signal generator was adjusted until a loud sound was heard at a particular frequency, known as the resonant frequency.

Describe how the student should use the oscilloscope to identify the resonant frequency and determine its value.

How did you do?

2b
Sme Calculator11 marks
The student reduced the volume V of air inside the bottle by adding known volumes of water. He recorded the following values of the resonant frequency f for each value of V.

V / cm3 f / Hz    
576 221    
476 244    
376 275    
276 323    
176 408    
126 485    

i)
Plot a graph of log f against logV on the grid opposite. Use the additional columns in the table to record your processed data.

(6)

ii)
It is suggested that the relationship between f and V is given by

f equals k V to the power of negative 1 half end exponent

where k is a constant.

Discuss whether the graph supports this suggestion.

(5)

q3bii-wph16-06-oct-2021-edexcel-int-as-and-a-level-phy

How did you do?

Did this page help you?

3a
Sme Calculator2 marks

A radioactive source emits beta radiation and gamma radiation.

State two precautions that should be taken when using this source.

How did you do?

3b
Sme Calculator2 marks

The radiation emitted from a radioactive source can be investigated using the apparatus shown. The Geiger-Muller (GM) tube detects beta radiation and gamma radiation.

q3b-wph16-06-jan-2022-edexcel-int-as-a-level-phy

The ratemeter displays the count rate from all radiation detected by the GM tube.

Explain why the background count rate should be measured.

How did you do?

3c
Sme Calculator2 marks

The corrected count rate C varies over time t according to the relationship

      C space equals space C subscript 0 e to the power of negative lambda t end exponent

where C0 is the initial count rate and λ is the decay constant.

Explain how a graph of ln C against t can be used to determine a value for λ.

How did you do?

3d
Sme Calculator10 marks

The source contained two radioactive isotopes, X and Y. The table below shows the corrected count rate as the isotopes decayed.

t / hours C / s−1  
0.00 633  
2.00 217  
4.00 167  
6.00 140  
8.00 126  
10.00 107  
12.00 98  



i)
Plot a graph of ln C against t on the grid opposite. Use the additional column in the table to record your processed data.

(5)

ii)
Isotope X has a half-life of approximately 30 minutes.

Determine a value of λ, in hours−1, for isotope Y.

(3)





λ = .............................. hours−1

iii)
Hence determine the half-life t1⁄2 for isotope Y.

(2)




t1⁄2 = ...............................

q3diii-wph16-06-jan-2022-edexcel-int-as-a-level-phy

How did you do?

Did this page help you?

4a
Sme Calculator4 marks

A student used the apparatus shown to investigate the time taken for a hollow cylinder to roll down a ramp.

q4-wph16-06-jan-2022-edexcel-int-as-a-level-phy

i)
The student measured the height h1 of the start line from the bench using a metre rule.

State two precautions she should take to ensure the measurement is as accurate as possible.

(2)

ii)
The student measured the height h2 of the finish line. She recorded the difference in height Δh between the start line and finish line as 65 mm ± 1 mm.

Explain why the uncertainty in Δh is 1 mm.

(2)

How did you do?

4b
Sme Calculator4 marks
The student placed the cylinder on the start line and released it. She immediately started a stopwatch and measured the time t for the cylinder to roll to the finish line. She repeated the measurements several times as shown.

t / s 2.10 1.86 1.94 1.89

    

i)
Calculate the mean value of t and its uncertainty.

(2)




Mean value of t = ............................... ± ..........................

ii)
The student made the ramp less steep by reducing the value of h1.

Explain how this might improve the measurement of t.

(2)

How did you do?

4c
Sme Calculator4 marks
Two students each carried out this procedure for another value of Δh. They recorded the following times for the same value of Δh.
Student t / s Mean t / s
A 2.45 2.50 2.38 2.41 2.44
B 2.48 2.45 2.43 2.40 2.44

Compare the accuracy and precision of the data that each student collected.

How did you do?

4d
Sme Calculator6 marks

The relationship between t and the acceleration of free fall g is given by

         t squared equals space fraction numerator 4 s squared over denominator g increment h end fraction

where s is the distance along the ramp between the start line and the finish line.

The student recorded the following values.

   t = 2.44 s ± 0.04 s
   s = 80.0 cm ± 0.1 cm
   Δh = 43 mm ± 1 mm

i)
Determine a value for g.

(2)




g = ..............................

ii)
Determine the percentage uncertainty in the value of g.

(2)




Percentage uncertainty = ...........................

iii)
Deduce whether the value of g is accurate.

(2)

How did you do?

Did this page help you?

5a
Sme Calculator3 marks

The time period of a rotating wheel can be determined using the apparatus shown.

q1-wph16-06-june-2021-edexcel-int-as-a-level-phy

A magnet is attached to the edge of the wheel. When the magnet passes the coil, a single pulse is displayed on the oscilloscope screen.

The horizontal axis of the oscilloscope screen represents time. The number of milliseconds per division on the horizontal scale can be adjusted.

As the wheel rotates, a series of pulses is displayed as shown.

q1a-wph16-06-june-2021-edexcel-int-as-a-level-phy

Describe how a value of the time period should be determined from these pulses.

How did you do?

5b
Sme Calculator4 marks
When the wheel is tested, the speed of the magnet is 22.2 ms–1.
The oscilloscope can be adjusted to give the following values for the horizontal scale.

millisecond per division 1 2 5 10

Explain which of these scales would display two complete pulses on the screen.
wheel diameter = 25.4 cm

How did you do?

Did this page help you?

6a
Sme Calculator4 marks

A student investigated the horizontal oscillations of a trolley between two springs using the apparatus shown.

q3-wph16-06-june-2021-edexcel-int-as-a-level-phy

The student used a stop clock to time the oscillations.

i)
Describe how he should modify the equipment to make his measurements as accurate as possible.



(2)

ii)
Describe two techniques he should use to reduce the uncertainty in the value of the time period.


(2)

How did you do?

6b
Sme Calculator14 marks
The student added masses to the trolley. He measured the total mass M of the trolley and masses. He recorded the following values of the time period T for each value of M.
M / kg T / s    
0.800 0.78    
1.300 1.01    
1.800 1.18    
2.300 1.34    
2.800 1.49    
3.300 1.60    

i)
Plot a graph of log T against log M on the grid opposite. Use the additional columns in the table to record your processed data.


(6)

ii)
The student predicts that the relationship between T and M is given by


T equals 2 pi square root of M over k end root

where k is the spring constant.
Discuss the validity of this prediction.


(5)

q3bii-wph16-06-june-2021-edexcel-int-as-a-level-phy

iii)
Determine the value of k.


(3)
k = .......................................................

How did you do?

Did this page help you?

7a
Sme Calculator3 marks

A student measured some dimensions of a thick, circular lens. The diagram shows approximate values of these dimensions.

q4-wph16-06-june-2021-edexcel-int-as-a-level-phy

i)
The student had a set of Vernier calipers and a micrometer screw gauge, as shown in the photograph.

q4ai-wph16-06-june-2021-edexcel-int-as-a-level-phy

State, with a reason, which of these measuring instruments she should use to measure the diameter d of the lens.

(1)

ii)
The student recorded the following values of d, measured at different points across the lens.

5.10 cm 5.11 cm 5.10 cm


She concluded that because her measurements were precise, they must be accurate.

Explain why this conclusion may not be justified.

(2)

How did you do?

7b
Sme Calculator2 marks
The student measured the thickness x of the edge of the lens using the micrometer screw gauge.
She recorded the following measurements.

x / mm
2.11 2.10 2.13 2.14 2.11

Calculate the mean value of x in mm and its uncertainty.



Mean value of x = ............................... mm ± ..........................mm

How did you do?

7c
Sme Calculator11 marks

The refractive index n of the material of the lens can be determined using

         n equals 1 plus fraction numerator d squared plus open parentheses t minus x close parentheses squared over denominator 8 f open parentheses t minus x close parentheses end fraction

where ff is the focal length of the lens.

i)
Determine the value of n.

d = 5.10 cm ± 0.01 cm
t = 8.30 mm ± 0.01 mm
f = 9.8 cm ± 0.3 cm


(2)
n = .......................................................

ii)
Show that the percentage uncertainty in open parentheses t minus x close parentheses is approximately 0.5 %.


(2)

iii)
Show that the uncertainty in d squared plus open parentheses t minus x close parentheses squared is approximately 0.11 cm.

(4)
iv)
The table shows data for some materials used to make lenses.

Material Pyrex Crown glass Flint glass
Refractive index  1.47 1.52 1.66


Deduce whether this lens could be made from one of these materials.


(3)

How did you do?

Did this page help you?