Circuit Diagrams (AQA GCSE Physics: Combined Science)

Revision Note

Test Yourself
Ashika

Author

Ashika

Expertise

Physics Project Lead

Circuit Diagrams

  • All students in the GCSE examination will be expected to recognise the following standard symbols and be able to construct circuits using them:

  • The function of the most common components are:
    • Cell / battery: Provides the circuit with a source of potential difference. A battery is two or more cells
    • Switch: Turn the circuit on (closed), or off (open)
    • Fixed resistor: A resistor limits the flow of current. A fixed resistor has a resistance it cannot change
    • Variable resistor: A resistor with a slider that can be used to change its resistance. These are often used in dimmer switches and volume controls
    • Thermistor: The resistance of a thermistor depends on its temperature. As its temperature increases, its resistance decreases and vice versa
    • Light-dependent resistor (LDR): The resistance of an LDR depends on the light intensity. As the light intensity increases, its resistance decreases and vice versa
    • Diode: A diode allows current to flow in one direction only. They are used to convert AC to DC current
    • Light-emitting diode (LED): This is equivalent to a diode and emits light when a current passes through it. These are used for aviation lighting and displays (TVs, road signs)
    • Ammeter: Used to measure the current in a circuit. Connected in series with other components
    • Voltmeter: Use to measure the potential difference of an electrical component. Connected in parallel with the relevant component

  • Each of these components have an electrical resistance that may impact the current in the circuit
    • However, the resistance of the ammeter and voltmeter are taken as negligible in exam questions

Drawing & Interpreting Circuit Diagrams

  • Being able to draw and interpret circuit diagrams using circuit symbols is an essential skill in the electricity topic
  • Electric circuit diagrams require the following to work effectively:
    • An energy source – This is a source of potential difference so a current can flow. This can be a cell, battery, or a power supply
    • closed path or a complete circuit – Electrons need to flow in a complete loop for a current to flow. A circuit can be open and closed using a switch
    • Electrical components – These could act as sensors that respond to the environment (LDR, thermistor), or measure a value (ammeter, voltmeter), or transfer electrical energy to other forms of energy (LED, lamp). These must be drawn with the correct circuit symbol

  • The key rules to remember are:
    • An ammeter is always connected in series
    • A voltmeter is always connected in parallel to the component the voltage is being measured
    • The direction of current flow is always from the positive to the negative terminal of the power supply

Worked example

Which circuit diagram correctly represents a circuit with current flowing through?WE - Circuit diagrams question image, downloadable AS & A Level Physics revision notes

WE - Circuit diagrams answer image, downloadable AS & A Level Physics revision notes

  • For a circuit to be connected, the switch must be closed
    • This is either circuit B or D

  • The other circuit symbol is a diode
    • Diodes only allow current to flow in one direction

  • Since current flow is from positive to negative, a forward-biased diode must point in this direction in order for the current to flow
    • This is seen in circuit B

Exam Tip

When asked to draw a circuit diagram, make sure to draw the wires as straight lines with a straight edge or a ruler and make it as neat as possible, especially the circuit symbols.

If the diagram is too small or there is ambiguity as to what a symbol represents, the examiner may not award you full marks!

Ashika, Physics Project Lead

Teacher tip

Ashika

Physics Project Lead

In my experience, students often overlook actively learning the circuit symbols. It is true that you will come to be familiar with most of them as you study the course, but it is really important that as part of your revision, you make sure that you know them all. You need to be able to name them and draw them. And for components such as thermistors, resistors, LDRs, fuses, and diodes, you also need to be able to explain how they work. 

You've read 0 of your 0 free revision notes

Get unlimited access

to absolutely everything:

  • Downloadable PDFs
  • Unlimited Revision Notes
  • Topic Questions
  • Past Papers
  • Model Answers
  • Videos (Maths and Science)

Join the 80,663 Students that ❤️ Save My Exams

the (exam) results speak for themselves:

Did this page help you?

Ashika

Author: Ashika

Ashika graduated with a first-class Physics degree from Manchester University and, having worked as a software engineer, focused on Physics education, creating engaging content to help students across all levels. Now an experienced GCSE and A Level Physics and Maths tutor, Ashika helps to grow and improve our Physics resources.